|
|
|
Component EMC
Specification JLR-EMC-CS v1.0
This engineering specification
addresses electromagnetic compatibility (EMC) requirements for electrical
and/or electronic components and subsystems for Jaguar Land Rover (JLR). These requirements have been developed to
assure compliance with present and anticipated International regulations in
addition to customer satisfaction regarding the EMC of vehicle systems.
JLR-EMC-CS
v1.0 replaces specification EMC-CS-2010JLR
JLR-EMC-CS
v1.0 must be used for all new and redesigned parts along with the latest Test
Plan Template.
Download JLR-EMC-CS
v1.0 inc Amendment 4 Specification
 Download JLR-EMC-CP v1.3 Compliance
Procedure (pdf
document)
Download JLR-EMC-TP v2.8 Test Plan Template
Amendments:
|
Date
|
Version
|
Revision
|
|
30-11-2013
|
v1.0
|
First release
|
|
12-12-2013
|
v1.0
Amendment 1
|
Correction -
Addition of peak limit in RE 310 DB-01
Addition of
ITS limit in RE 310 MS-20
Correction – RI
112 Para 1, start frequency corrected to 0.1 MHz in line with Figure 10‑1
Correction –
RI 112 Table 10‑2, 0.1 to 1 MHz range included in line with
Figure 10‑1
Correction –
CI 265 Table 18‑1, note 1: 1 hour observed, 7 hours
unobserved
|
|
13-01-2014
|
v1.0
Amendment 2
|
Correction –
RE 310 frequency range ends at 5905 MHz
Amendment – CE420
removal of voltage method
Correction –
RI 112 Figure 10‑1, Band 1 Level 1 84 dBµA
Correction –
RI 112 start frequency of 0.1 MHz noted throughout
Correction –
RE 320 Figure 11‑1, f
= frequency in Hz
Correction –
RI 140 Figure 12‑1, Frequency range corrected to 20 – 100 Hz
Correction –
RI 140 Figure 12‑2, Key numbering restarted at 1
Correction –
CI 250 clarification - both test
configurations required (Figure 17‑5a & b)
Correction –
CI 265 Table 18‑1, Waveform A test duration 13 bursts
Correction – CI 265 Figure 18‑1, T1 & T2 min 2 ms and T1 & T2 max 4
ms removed
Correction –
CI 220 Annex C Figure C-7, tr = 1 µs - aligned with ISO 7637-2
|
|
28-03-2014
|
v1.0
Amendment 3
|
Correction –
CE420 Voltage changed to current in Section 8.2.1 & inclusion of probe positions
Clarification
– RI 112 All connector looms shall be tested individually and combined
Clarification
– RI 140 30,000µF capacitor shall be omitted from test configuration
Clarification
– CI 220 Annex C, Figure C-10, clarification of multiple Us* levels
|
|
25-02-2015
|
v1.0
Amendment 4
|
Correction – Para 5.6 - For the GSM
bands a minimum ambient of 2 dB below the average test limit is acceptable.
Clarification – RE 320, MIL-STD-461E
loop antenna may be used providing the ambient emissions level can be
achieved and the test is performed in accordance with DRE02.B.
Clarification – RI 140, MIL-STD-461E loop antenna may be used
providing the immunity level can be achieved and the test is performed in
accordance with DRSO1.B.
Clarification – Annex H, For Crank
Waveforms B, C and D, the set-up is the same as shown in Figure 16‑2 for CI 230 but
without the thermal chamber.
Correction – CI 280 unpowered, extension pin now required for plastic
and metal connector bodies.
Correction – RE 320 – Table 11‑1 Frequency Step
is now 0.005, 0.05, and 0.5, in-line with DRE02.B
Clarification – RE 320 – Limit is peak
Correction – RE310 - Table 7‑1: R-01 and R-02,
changed frequency from 0.15 to 0.1
Clarification – RI 114 - Tests with both horizontal and vertical
antenna polarizations shall be performed, except 200 MHz to 400 MHz where
only vertical polarization is required
Clarification – Figure F-2 - For Flexray
the termination resistors must be changed from 60 to 50 ohms.
Clarification – RE310 - The battery negative wire shall be connected
to the ground plane.
|
Superseded Component EMC
Specification EMC-CS-2010JLR v1.2
EMC-CS-2010JLR v1.2
is superseded from 1 December 2013 and can only be used for programmes that
have already been contracted.
MQ-7012
v1.3 supplement to EMC-CS-2010JLR v1.2
This
supplement contains additional requirements that are to be implemented to
existing components which were contracted to EMC-CS-2010JLR v1.2. This applies to all components where
testing has not yet been completed even though the component may not have
been contracted to meet these additional requirements. This MQ-7012 is now
incorporated in to JLR-EMC-CS.
Optional
Test Method:
The use of EMI receivers
with Fast Fourier Transform (FFT) capability for performing emissions measurements (i.e. RE 310,
CE 420, RE 320), that meet the requirements of CISPR 16-1-1 edition 3.2,
amendment 1 are now permitted.
Test
Fixture for RI 130 and RI 150:
This fixture
facilitates improved testing regardless of the number of interface circuits
of the product. Click here
for details with respect to construction of this device. Note that all
recognized EMC labs who construct their own fixture must perform parametric
measurements to verify the fixture is constructed correctly.
Although not required by Jaguar Land Rover, the fixture may be purchased
commercially from Rohde and Schwarz (part number RSA TS-RI130-Fix).
|